Strain hardening behaviors and mechanisms of polyurethane under various strain rate loading

The uniaxial tension experiments are performed on thermoplastic polyurethane to investigate its mechanical behaviors and related potential mechanisms, and the loading strain rate is designing to be wide ranging from 0.0001 to 1 s⁻¹. It is found that the polyurethane presents an obvious rate-dependence, and the stress strain curves share distinct strain hardening characteristics under the investigated strain rates. Furthermore, the strain hardening ratios are sharing nearly same trends and appear to be influenced by both strain rate and the induced adiabatic heating. Besides, the ratio is also strain-dependent on previous loading history. Then, a two-dimension unit cell model is built to investigate potential equivalent mechanisms, of which the hard phase as inclusion is equivalent with crystallization zone, crosslinking sites, and so forth. The simulation results facilitate to explain the distinct strain hardening ratios, even for the matrix from the extrapolated curves under super-low strain rate loading. Finally, the analogic mechanisms of equivalent hard inclusions are proposed, which can reasonably explain the strain rate- and strain-dependence characteristics of polyurethane mechanical behaviors.     

Photoluminescence and temperature sensing of lanthanide Eu3+ and transition metal Mn4+ dual-doped antimoniate phosphor through site-beneficial occupation

For a long time, rare-earth ion-doped phosphors have been widely used in temperature sensing because of their excellent light-emitting properties. However, most of the rare earth elements are relatively rare and expensive, so the transition group elements that are economical and easy to obtain have been favored by researchers. This paper presents a new type of phosphor doped with rare earth ion and transition metal for optical temperature measurement. In recent years, Mn⁴⁺-doped phosphors have attracted wide attention because of their strong deep red light-emitting properties. La₂LiSbO₆ provides a good host environment for Mn⁴⁺ and Eu³⁺ due to its unique crystal structure. In this paper, a series of La₂LiSbO₆ phosphors singly doped with Mn⁴⁺ and Eu³⁺, and co-doped with Eu³⁺/Mn⁴⁺ were synthesized. The crystal phases and optical properties of these materials were characterized and analyzed in detail. We specifically studied the temperature dependence of the fluorescence intensity of the optimized La₂LiSbO₆: Eu³⁺, Mn⁴⁺ phosphors at 303K–523K. The experimental results prove that the thermal responses of Mn⁴⁺ and Eu³⁺ are different. With increasing temperature, the thermal quenching of the Mn⁴⁺ fluorescence intensity is much faster than that of Eu³⁺, so the temperature characteristics can be explored by the fluorescence intensity ratio (FIR) of Eu³⁺ to Mn⁴⁺. At 523 K, its maximum relative sensitivity and maximum absolute sensitivity can reach 0.891% K⁻¹ and 0.000264 K^-1, respectively. Our experimental analysis shows that La₂LiSbO₆:Eu³⁺/Mn⁴⁺ phosphors have relatively high temperature sensitivity and have potential application prospects in the field of high temperature sensing.     

剂油比对煤焦油沥青质加氢过程的影响

以中低温煤焦油沥青质为原料,采用NiMoW/γ-Al_2O_3商业催化剂,在反应温度380℃、反应压力8 MPa和反应时间1.5 h条件下,分别在不同剂油质量比(1∶25、1∶20、1∶15、1∶10)条件下进行加氢实验,通过采用元素分析、FT-IR、XRD、~1H-NMR和XPS等分析表征手段,考察不同剂油质量比对中低温煤焦油沥青质加氢转化过程的影响。结果表明,随着剂油质量比的增加,沥青质转化率提高,加氢产物分布也发生大幅变化,沥青质和芳香分轻质化转化为饱和分。但随着剂油质量比的进一步提高,同时也发生了更多的裂化反应和缩合反应,剂油质量比在合适范围能够很好地起到加氢轻质化且抑制结焦的效果。     

车门内饰板优化分析及模具设计

利用CAE分析软件Moldex3D先找出整个设计是否存在缺陷,为了增加优化效率,采用田口实验设计法规划控制因子与配置。L9(34)直交表来求得成型条件的最佳化参数组别,观察结果并找出最佳成型条件,以降低成型后所发生的体积收缩率以及翘曲位移量。由S/N因子反应表可看出对于Z轴变形量在塑料温度209℃、保压时间11.025 s、冷却时间17.85 s时较优良。Z轴的翘曲从1.64 mm降低到1.04 mm,整体改善了36.5%,最终根据优化结果进行了模具设计。     

Liquid yield from juniper and mesquite bio‐fuel gasification

Mesquite (Prosopis glandulosa) and redberry juniper (Juniperus pinchotii) are two woody species which dominate uncultivated lands in the south central Great Plains, USA (Texas, Oklahoma) and may have potential for bioenergy utilization. In this study, these two biomasses were gasified in an adiabatic, updraft fixed‐bed gasifier using air as medium. The products include low heating value gas and liquid tar yield. The effects of fuel moisture content and the equivalence ratio (ER) on liquid yields including heavy tar and light tar and higher heating value (HHV) of the producer gas were investigated. It was found that updraft gasifiers produce a large amount of tar, in a range of 100 g/Nm³ of gas produced. As the equivalence ratio (ER) increased (i.e. more rich char conditions), peak temperature (T_peak) within the bed decreased due to the lesser partial oxidization. The liquid yield showed peak value with change in moisture content between 6 and 24%. Heavy tar is a very high quality fuel with a higher heating value of over 29 MJ/kg on a dry, ash‐free (DAF) basis which is a slightly higher than that of ethanol. Copyright © 2015 John Wiley & Sons, Ltd.     

注采比对“二三结合”开发模式渗流特征的影响

大庆油田的开发逐渐进入高含水阶段,厚油层动用程度低,"二三结合"开发模式是有效的提高厚油层动用程度,改善水驱开发效果,提高油田采收率的有效手段。在"二三结合"开发模式注聚阶段中注采比对井间压力、含水饱和度等变化有重要影响。为了探究注采比对开发层位的井间压力及饱和度的影响,利用油藏数值模拟方法,模拟了相同的开发模式不同注采比的生产情况,绘制了不同注采比情况下,不同层位的井间压力及含水饱和度变化情况,为维持地层压力平衡,保持油田稳定生产提供有力的依据。     

Study of metal assisted anisotropic chemical etching of silicon for high aspect ratio in crystalline silicon solar cells

Textured surface is commonly used to enhance the efficiency of silicon solar cells by reducing the overall reflectance and improving the light scattering. In this study, a comparison between isotropic and anisotropic etching methods was investigated. The deep funnel shaped structures with high aspect ratio are proposed for better light trapping with low reflectance in crystalline silicon solar cells. The anisotropic metal assisted chemical etching (MACE) was used to form the funnel shaped structures with various aspect ratios. The funnel shaped structures showed an average reflectance of 14.75% while it was 15.77% for the pillar shaped structures. The average reflectance was further reduced to 9.49% using deep funnel shaped structures with an aspect ratio of 1:1.18. The deep funnel shaped structures with high aspect ratios can be employed for high performance of crystalline silicon solar cells.     

负泊松比针织结构及其应用

本文对各个负泊松比材料的作用原理进行概括和总结,并简要介绍了目前用针织技术实现负泊松比结构的方案,包括平面经编织物、三维间隔织物、纬编折叠结构织物等。最后对负泊松比结构针织物在服用和产业用方面广泛的潜在应用分别进行了介绍,并展望了负泊松比结构针织物在以后研究中的发展方向及前景。     

A procedure for design of hydrogen networks with multiple contaminants☆

It is necessary to reduce hydrogen consumption to meet increasingly strict environmental and product-quality regulations for refinery plants. In this paper, the concentration potential concepts proposed for design of water-using networks are extended to synthesis of hydrogen networks with multiple contaminants. In the de-sign procedure, the precedence of processes is determined by the values of concentration potential of demands. The usage of complementary source pair(s) to reduce utility consumption is investigated. Three case studies are presented to il ustrate the effectiveness of the method. It is shown that the design procedure has clear engineer-ing meaning.     

Difference angle quantization index modulation scheme for image watermarking

In this paper, we propose a new angle quantization index modulation (AQIM) method, called the difference AQIM (DAQIM) method. The proposed method aims to improve the watermarking performance against gain attacks. Unlike the original AQIM method (Ourique et al., Angle QIM: a novel watermark embedding scheme robust against amplitude scaling distortions, in: Proceedings of IEEE International Conference on Acoustics, Speech, and Signal Processing, vol. 2, 2005, pp. 797–800), the DAQIM method quantizes the difference of the two angles instead of the angles themselves. The main advantage of the DAQIM method is to disperse the interference to the watermark signal from one angle to more angles. Thus, the watermark has a higher ability to resist attacks. We perform a theoretical analysis of the document-to-watermark ratio (DWR) based on our proposed method. We show that our proposed method can obtain a lower embedding distortion compared to the AQIM and the gradient direction watermarking (GDWM) (Nezhadarya et al., IEEE Trans. Inf. Forensics Secur., 6(4), 2011, 1200–1213), methods under the same robustness and payload conditions. The experimental results demonstrate that our proposed method outperforms common existing methods in terms of the robustness against various attacks such as the JPEG quantization noise, additive white Gaussian noise (AWGN), cropping effect and mean filtering.